By Ferhan Bugay, Executive Director, Aero Support Group · 18 November 2026
AS9100D and AS9110C are being replaced by IA9100 and IA9110. As of 18 November 2026, neither standard has been published and the IAQG has not set a transition deadline. The IAQG’s own change summaries point to new requirements on quality culture, ethics, information security, product safety, counterfeit and unapproved parts, and control of sub-tier suppliers.
If you run quality at a maintenance organisation that holds AS9110, or an AS9100 supplier that also does repairs, this article sets out what is confirmed, what is still expected, and what you can prepare now without waiting for the final text. A free readiness check is at the end.
What is confirmed and what is still expected
| Item | Status on 18 November 2026 |
|---|---|
| ISO 9001:2026 | Published on 16 September 2026. ISO 9001:2015 certificates are expected to remain valid until 30 September 2029, subject to the final determination of Global Accreditation Cooperation. |
| New names | AS9100, EN9100 and JISQ9100 will be published as IA9100. The maintenance standard becomes IA9110 and the distributor standard IA9120. |
| Publication of IA9100 and IA9110 | Not yet published. No publication notice from the IAQG or SAE. Industry estimates range from late 2026 to 2027. |
| Transition deadline | Not announced. Certification bodies report a single transition date for all of them, set out in an IAQG supplemental rule. |
| AS9100D and AS9110C certificates | Remain valid until the transition rules say otherwise. |
Why AS9100 becomes IA9100
Until now the same standard has been published three times: AS9100 by SAE in the Americas, EN9100 in Europe and JISQ9100 in Asia. The IAQG is moving to one standards development organisation and one international designation, IA (International Aerospace). The content stays a single text, as it already was. What changes is that you will no longer see three regional codes for the same requirements.
Two revisions, two transitions
Certification bodies that briefed their clients after the IAQG’s October 2025 meeting describe two steps:
- A limited revision of 9100, 9110 and 9120, still based on ISO 9001:2015, with about eight changes focused on supplier control. The transition is reported as 8 to 13 months, with one transition date for every certification body and certificates reissued afterwards.
- A full revision aligned with ISO 9001:2026, reported as planned for 2027, with a longer transition that most expect to be three years.
Both steps are reported by certification bodies, not yet published by the IAQG as final rules. Ask your certification body which step your next audit will cover.
Expected changes in IA9100
The IAQG published a key change summary for IA9100 in November 2023, based on the coordination draft. The clause numbers below come from that summary and may move in the final text.
| Area | Clause (draft) | Expected change |
|---|---|---|
| Quality culture | 0.1, 5.1.1 | Leadership sets quality culture goals that fit the policy, vision, mission, values and context. |
| Ethics | 5.1.1, 7.3 | Leadership promotes an ethical work environment. The note lists policy, conduct expectations, training, reporting channels, investigation and protection from retaliation. |
| Information security | 7.1.7, 7.5.3.1, 8.1 | New requirement to plan, implement and control information security for the QMS, with data protection for electronic records. |
| Product safety | 8.1.3 | The notes become requirements: hazard identification, risk control, change management, effectiveness, training, communication and reporting of safety events to customers, authorities and type certificate holders. |
| Counterfeit parts | 8.1.4 | The notes become requirements: training, obsolescence monitoring, approved sources, traceability, test methods, monitoring of external reports, segregation and reporting. |
| Foreign object debris | 8.1 k | Operations must prevent, detect and mitigate FOD risk. |
| External providers | 8.4 | Control extended to direct and sub-tier providers. Remote inspection and audit of suppliers allowed. |
| Planning methods | 7.1.5.1, 8.1 notes | APQP named as one planning method; measurement system analysis and control plans added in notes. |
| Performance and audit | 9.1, 9.2 | Review of performance indicators becomes a requirement. The audit programme must include risks. |
| Improvement | 10.3 | Periodic QMS maturity assessments with improvement goals. |
What IA9110 means for maintenance organisations
The IAQG’s IA9110 clause-by-clause summary (June 2024) carries over most of the IA9100 changes and adds items written for maintenance. For an MRO quality manager, these are the ones that will show up in audit questions:
- Safety policy (5.2.3): safety objectives, confidential reporting with no retaliation and continual safety improvement must be stated.
- Confidential reporting (8.1.3 h): a confidential reporting system becomes a requirement, with a note on anonymous reporting.
- Suspected unapproved parts (8.1.5): training, obsolescence monitoring, traceability, test methods, monitoring, segregation, containment and reporting move from notes into requirements.
- Competence before certification (7.2 h): competence must be checked before personnel qualification or certification, not only before unsupervised work. Expect auditors to compare competence assessment dates with authorisation dates.
- Configuration management (8.1.2): the CAMO is named as a stakeholder.
- Transfer of work (8.1, note 3): moving work to another location, housing or facility must be planned.
- New capability (8.5.1.4): evaluation of a new capability with a First Process Evaluation. IAQG guidance for this is still being written.
- Late corrective action (5.1.1 n): leadership must act in due time when corrective actions are late or not effective.
- Safety objectives (9.3): their performance must be evaluated.
How IA9110 lines up with EASA Part-145
Most AS9110 organisations also hold a Part-145 approval. Many of the expected IA9110 changes cover ground that Part-145 already requires, which means the evidence may already exist in your management system. The table points to the Part-145 requirement. It does not claim that one satisfies the other: the auditor will still check the IA9110 wording against your records.
| Expected IA9110 change | Related Part-145 requirement |
|---|---|
| Product safety process, hazard identification and risk control | 145.A.200(a)(3) safety risk management |
| Confidential safety reporting | 145.A.202 internal safety reporting scheme |
| Reporting of safety events to authorities and type certificate holders | 145.A.60 occurrence reporting |
| Information security | 145.A.200A information security management system (Part-IS, applicable from 22 February 2026) |
| Suspected unapproved parts | 145.A.42 components, acceptance and segregation |
| Foreign object debris | 145.A.48(c)(1) general verification that the aircraft or component is clear of tools and extraneous parts |
| Competence before certification | 145.A.30(e) and 145.A.35 competence and certifying staff |
| Sub-tier and contracted providers | 145.A.205 contracting and subcontracting |
| Risk-based audit programme | 145.A.200(a)(6) compliance monitoring |
Part-145 point 145.A.200(c) already allows the management system to be integrated with other certificates. One integrated system with one set of records is easier to audit than an AS9110 system sitting next to a Part-145 system.
How to prepare before the final text
- Ask your certification body which revision your next surveillance or recertification audit will cover, and when their auditors will be trained on the new standards.
- Run a gap check against the expected changes. Score what you can show today, not what the manual says.
- Start with the items that are already Part-145 requirements: confidential reporting, information security under Part-IS, suspected unapproved parts and competence records. These cost least because the work is partly done.
- Review purchase orders and supplier agreements for sub-tier flow-down. Supplier control is the focus of the limited revision, so it is likely to come first.
- Plan your ISO 9001:2026 gap assessment in parallel. The full IA revision will build on it.
- Do not rewrite your quality manual yet. Wait for the published text, then change the manual once.
Our article on Annex 19, 3rd edition, for MROs and CAMOs covers the safety management side, and the ISO 9001:2026 maturity assessment covers the base standard.
References
- IAQG, IA9100 Key Changes, System View (November 2023)
- IAQG, IA9100 Key Change Summary, Clause View
- IAQG, IA9110 Key Changes, Clause View (June 2024)
- ISO 9001:2026, Quality management systems. Requirements
- EASA, Easy Access Rules for Continuing Airworthiness (Regulation (EU) No 1321/2014, Annex II Part-145)
Need support with an AS9110 to IA9110 gap assessment or with integrating AS9110 and Part-145? See our EASA Part-145 consulting, quality management systems and internal audit services, or write to info@aerosupport360.com.
Free download: IA9100 / IA9110 Readiness Check
An Excel workbook with 31 expected changes taken from the IAQG key change summaries. Choose the certificate you hold, AS9100D or AS9110C, and the checklist shows the rows that apply to you, with a Part-145 pointer for MROs. Score each row from 0 to 4 and the dashboard shows readiness by theme. Rows below your threshold go into an action plan with a priority.
The tool is based on draft-stage summaries. We will issue a new revision when IA9100 and IA9110 are published.
We use your details to send you the download link and to follow up on your request. If you tick the box above, we will also send you occasional ASG updates. We do not share them with third parties. See our Privacy Policy.
Frequently asked questions
No. As of 18 November 2026, neither IA9100 nor IA9110 has been published, and there is no publication notice from the IAQG or SAE. Industry estimates range from late 2026 to 2027.
The IAQG has not announced a transition deadline. Certification bodies report a short transition for a limited revision focused on supplier control, with one transition date for all certification bodies, followed by a longer transition for the full revision aligned with ISO 9001:2026. Your certification body will confirm the dates that apply to your certificate.
Yes. Current certificates remain valid until the transition rules say otherwise.
AS9100 is the quality management system standard for organisations that design and produce aviation, space and defence products. AS9110 is written for organisations whose main business is maintenance of commercial and military aircraft products, including OEM maintenance operations run separately from production. Both will move to the IA designation: IA9100 and IA9110.
No. AS9110, and IA9110 after it, is a voluntary industry certification issued by a certification body. Part-145 is a regulatory approval issued by the competent authority. Many MROs hold both, and Part-145 point 145.A.200(c) allows the management system to be integrated with other certificates.
The full revision is planned to align with ISO 9001:2026. Certification bodies report that the limited revision, expected first, stays on ISO 9001:2015.
Subscribe to Global Aviation Safety Radar
Weekly aviation safety and compliance intelligence covering ICAO, IATA, EASA, and UK CAA developments — translated into practical implications for airlines, MROs, airports, ground handlers, and aviation leaders.